更新時間：2022-08-01
文章來源：http://m.djfrj.net.cn/
閱讀量：22
舞臺燈光設備隨著科技的發展也是越來越越來越智能，當然在操作舞臺燈光設備的時候我們一定要小心，以防弄壞燈光設備，那么舞臺燈光設備進行操控時應注意什么呢？
With the development of science and technology, stage lighting equipment is becoming more and more advanced and intelligent. Of course, we must be careful when operating stage lighting equipment to prevent damage to the lighting equipment. What should we pay attention to when operating stage lighting equipment?
一、在燈泡處于冷的狀態下，去猛然間的推亮(滿)燈光，結果就很可能會(huì )造成燈泡“啪”的一聲爆碎；或是造成燈泡的鎢絲熔斷、正確的操作是：
1、 When the bulb is cold, push the light suddenly (full), and the result is likely to cause the bulb to "snap" and burst; Or the tungsten wire of the bulb is blown, and the correct operation is:
當燈泡是處在冷的狀態下(開場前)時，將操控臺的推子試探的只推起一點(常說的壓光狀態)，使燈泡微亮，讓其處在預熱狀態，使其受熱均勻，同時也可以蒸發掉那些凝結在燈泡玻璃殼上的水分子，預熱數分鐘后，再推亮一點，再預熱數分鐘后，這個時候才可將燈光完全的推亮。
When the bulb is in a cold state (before the opening), push up the pusher of the console tentatively only a little (often referred to as the calendering state), so that the bulb is slightly bright, so that it is in a warm-up state, so that it can be heated evenly. At the same time, it can also evaporate the water molecules condensed on the bulb glass shell. After preheating for several minutes, push it on a little, and then preheat for several minutes, then the light can be completely pushed on at this time.
二、切忌將調光臺的推子在推滿的狀態下，再去打開硅箱的電源。其結果和上述的結果就會(huì )相同，兩樣都是會(huì )損壞燈泡的。這個時候應該將調光臺所有的推子處于關閉狀態，在打開硅箱電源。
2、 Never turn on the power of the silicon box when the pusher of the dimmer is full. The result will be the same as the above results, both of which will damage the bulb. At this time, all the faders of the dimmer should be turned off and the power of the silicon box should be turned on.
三、提醒各位切忌在開關設備時，將燈控臺和硅箱電源的順序顛倒了。開啟電源時，要先打開燈控臺的電源，再打開硅箱的電源的;而在關閉電源時，則要先關閉硅箱的電源，后關閉燈控臺的電源。
3、 Remind you not to reverse the order of light console and silicon box power supply when switching equipment. When turning on the power supply, first turn on the power supply of the light console, and then turn on the power supply of the silicon box; When turning off the power, turn off the power of the silicon box first, and then turn off the power of the light console.
四、切忌在燈泡推亮時，大動作搖晃燈具。燈泡的鎢絲是會(huì )因此而斷裂或脫落的。因為燈泡在點亮后，溫度逐漸升高，鎢絲也會(huì )相應地會(huì )變軟，同時也會(huì )受到地心引力的影響，鎢絲也就相應的下垂，若在此時大動作的去搖晃燈具時，也是要等到燈光完全冷卻后方可拆卸的。
4、 Never shake the lamp with big movements when the bulb is turned on. The tungsten wire of the bulb will break or fall off because of this. Because after the bulb is lit, the temperature gradually rises, and the tungsten wire will correspondingly soften. At the same time, it will also be affected by gravity, and the tungsten wire will correspondingly sag. If you shake the lamp in a big action at this time, you can't disassemble it until the light is completely cooled.
五、
山東舞臺燈光廠家提醒您，不要在更換燈泡時，直接選擇用手去接觸燈泡，這是會(huì )影響燈泡的光潔度，而另一個隱性的危害是導致燈泡的爆碎、在更換燈泡時，一定會(huì )先戴上手套，再去接觸燈泡的。而如果沒有手套，也是可用包裝燈泡的海棉、塑料紙或柔軟的紙巾包裹，再進行安裝，而在安裝之后也是一定要記得將這些包裹物取下來，以免在推亮燈泡時會(huì )引發火災。
5、 Shandong stage lighting manufacturers remind you not to directly choose to touch the bulb by hand when replacing the bulb, which will affect the smoothness of the bulb, and another hidden hazard is that it will cause the bulb to burst. When replacing the bulb, you must wear gloves first and then touch the bulb. If you don't have gloves, you can also wrap the bulb with sponge, plastic paper or soft paper towels before installation. After installation, you must remember to remove these packages to avoid fire when pushing the bulb on.
此外切忌將所安裝燈光的功率超過了廠家所規定的功率，若是只考慮燈泡在熔斷的瞬間所產生的電流的話，那是非常片面的看法。所以您在使用相關設備之前應該會(huì )有所了解的，更多信息就來我們網站
http://m.djfrj.net.cn獲取吧。
In addition, the power of the installed light should not exceed the power specified by the manufacturer. It is a very one-sided view to consider only the current generated by the bulb at the moment of fusing. So you should know something before using relevant equipment. For more information, please come to our website http://m.djfrj.net.cn Get it.
魯公網安備 37010202002516號
